As you may have seen in this other post here I have an interest in this Amiga hard drive controller designed for the Commodore Amiga 500. I used this for years to interface an HDD. At the time I took some photos of the...
Layout 1
Layout 2
2-wire digital voltage display accuracy
I had a few needs to for a simple voltage display that can handle the range of +5v to +12v. There’s a few different applications like displaying the state of a battery, a state of a power supply and so on. I was...
Refilling Star Micronics NX-1020 black ribbon ink cartridges
I have an old Star Micronics NX-1020 Rainbow printer from circa 1993. I bought this printer using my paper route Christmas money that I saved up for months. The printer served me valiantly throughout the early 90s. This...
Layout 3
Some reverse engineering notes on DataFlyer 500 BUSS Pal
As you may have seen in this other post here I have an interest in this Amiga hard drive controller designed for the Commodore Amiga 500. I used this for years to interface an HDD. At the time I took some photos of the...
2-wire digital voltage display accuracy
I had a few needs to for a simple voltage display that can handle the range of +5v to +12v. There’s a few different applications like displaying the state of a battery, a state of a power supply and so on. I was...
Refilling Star Micronics NX-1020 black ribbon ink cartridges
I have an old Star Micronics NX-1020 Rainbow printer from circa 1993. I bought this printer using my paper route Christmas money that I saved up for months. The printer served me valiantly throughout the early 90s. This...
HP Agilent 5382A tear down with photos
I recently tore down an Agilent E5382A Flying Lead Set. I used a Torx T-4 bit to remove the (4) tiny tiny screws. This adapter has a 90-pin connector that comes from HP logic analyzer cards, and then goes out to single...
Layout 4
Some reverse engineering notes on DataFlyer 500 BUSS Pal
As you may have seen in this other post here I have an interest in this Amiga hard drive controller designed for the Commodore Amiga 500. I used this for years to interface an HDD. At the time I took some photos of the...
2-wire digital voltage display accuracy
I had a few needs to for a simple voltage display that can handle the range of +5v to +12v. There’s a few different applications like displaying the state of a battery, a state of a power supply and so on. I was...
Refilling Star Micronics NX-1020 black ribbon ink cartridges
I have an old Star Micronics NX-1020 Rainbow printer from circa 1993. I bought this printer using my paper route Christmas money that I saved up for months. The printer served me valiantly throughout the early 90s. This...
HP Agilent 5382A tear down with photos
I recently tore down an Agilent E5382A Flying Lead Set. I used a Torx T-4 bit to remove the (4) tiny tiny screws. This adapter has a 90-pin connector that comes from HP logic analyzer cards, and then goes out to single...
Setting up a SCSI2SD on HP 167xxA for CDROM and HDD targets
This quick guide contains instructions on how to setup, configure, burn, and launch an install from a SCSI2SD when inserted into an HP/Agilent Logic Analyzer on the 16700 series. A fresh install is always recommended...
Layout 5
Some reverse engineering notes on DataFlyer 500 BUSS Pal
As you may have seen in this other post here I have an interest in this Amiga hard drive controller designed for the Commodore Amiga 500. I used this for years to interface an HDD. At the time I took some photos of the...
2-wire digital voltage display accuracy
I had a few needs to for a simple voltage display that can handle the range of +5v to +12v. There’s a few different applications like displaying the state of a battery, a state of a power supply and so on. I was...
Refilling Star Micronics NX-1020 black ribbon ink cartridges
I have an old Star Micronics NX-1020 Rainbow printer from circa 1993. I bought this printer using my paper route Christmas money that I saved up for months. The printer served me valiantly throughout the early 90s. This...
HP Agilent 5382A tear down with photos
I recently tore down an Agilent E5382A Flying Lead Set. I used a Torx T-4 bit to remove the (4) tiny tiny screws. This adapter has a 90-pin connector that comes from HP logic analyzer cards, and then goes out to single...
Setting up a SCSI2SD on HP 167xxA for CDROM and HDD targets
This quick guide contains instructions on how to setup, configure, burn, and launch an install from a SCSI2SD when inserted into an HP/Agilent Logic Analyzer on the 16700 series. A fresh install is always recommended...
Layout 6
Layout 7
Layout 8
2-wire digital voltage display accuracy
I had a few needs to for a simple voltage display that can handle the range of +5v to +12v. There’s a few different applications like displaying the state of a battery, a state of a power supply and so on. I was...
HP Agilent 5382A tear down with photos
I recently tore down an Agilent E5382A Flying Lead Set. I used a Torx T-4 bit to remove the (4) tiny tiny screws. This adapter has a 90-pin connector that comes from HP logic analyzer cards, and then goes out to single...
Evaluating Battery Backup Solutions for CPAP machines
I recently had a need to provide a battery backup solution for a CPAP machine. A CPAP machine helps people, who suffer from sleep apnea, get a good night’s rest. About 20 million Americans suffer from this...
Layout 9
Layout 10
Some reverse engineering notes on DataFlyer 500 BUSS Pal
As you may have seen in this other post here I have an interest in this Amiga hard drive controller designed for the Commodore Amiga 500. I used this for years to interface an HDD. At the time I took some photos of the...
Refilling Star Micronics NX-1020 black ribbon ink cartridges
I have an old Star Micronics NX-1020 Rainbow printer from circa 1993. I bought this printer using my paper route Christmas money that I saved up for months. The printer served me valiantly throughout the early 90s. This...
Setting up a SCSI2SD on HP 167xxA for CDROM and HDD targets
This quick guide contains instructions on how to setup, configure, burn, and launch an install from a SCSI2SD when inserted into an HP/Agilent Logic Analyzer on the 16700 series. A fresh install is always recommended...